How To Reset Ring Spotlight Camera? (Solved)

Battery for the Ring Spotlight Cam

  1. The setup button may be found on the top of the camera.
  2. Press and hold the setup button for a total of 10 seconds. When the light on the front of the camera starts flashing, the reset is complete. When the light goes out, the reset is complete.

Why is my Ring spotlight camera not working?

Unplug your router for 30 seconds, and then reconnect it to the network. Check to see whether your Spotlight Cam reconnects automatically. Remove the internal battery and then replace it with a new one. Wait 10 seconds before pressing it a second time to see if your Ring automatically reconnects to your phone.

How do I reconnect my spotlight camera to Ring?

In order to reconnect your doorbell or security camera wifi in the Ring App, please follow these steps:

  1. Devices may be accessed by tapping the three lines in the upper left corner. Choose the doorbell or security camera that has to be reconnected to the internet. The Device Dashboard is displayed on the following screen. Tap on Device Health.
  2. Tap on Reconnect to Wifi or Change Wifi Network.
  3. Tap on Restart Device.
You might be interested:  Why Do My Ears Ring When I Stand Up?

Where is the set up button on a Ring spotlight camera?

To set the device into Setup Mode, press and hold the little button on the top right corner of the camera for a couple of seconds. What is the purpose of Setup Mode? In setup mode, any Ring product broadcasts a temporary wifi network that may be accessed by other Ring products.

How do I reset my outdoor ring camera?

1 Reset the Spotlight/Floodlight Camera to its factory settings

  1. Check to see that the camera is operational. For 30 seconds, press and hold the reset button located on the top of the camera. Following the release of the button, the status light at the bottom of the camera will blink a few times, indicating that the camera is restarting. The camera has now been restored to its original settings.

How do I reset my doorbell ring camera?

To do a hard reset, hold down the orange button for 20 seconds while pressing the power button. Following the release of the button, the light on the front of the Ring Doorbell will blink a few times, signaling that your Ring Doorbell is restarting. It may take up to a minute to finish this procedure completely.

How do I factory reset my indoor Ring camera?

When you reset a Ring Stick Up Cam to its factory default configuration, all of its previously saved settings and preferences will be lost.

  1. Check to see that the camera is switched on or that the battery is fully charged. Hold the reset button on the back of the camera for 15 seconds while pressing and holding it. Press and hold the button until it is released. The camera has now been restored to its original settings.
You might be interested:  What Does A Ring On The Right Ring Finger Mean? (Best solution)

Why is my Ring camera offline?

Why are Ring devices prone to going offline? You experience a brief loss of power. A wire in your router’s configuration becomes loose for a brief period of time. You have changed the password for your Wi-Fi network. Because of a drained battery, the power of your Ring gadget is significantly reduced.

Why Does My Ring floodlight keep going offline?

The loss of electricity is by far the most common reason for a network connection to be lost. Power surges and problems with the power connections are examples of what is meant by this. To see whether your Floodlight Cam has lost its power, do the following: The Floodlight Cam is attached to a light switch; thus, it is important to check to determine whether the light switch has been mistakenly turned off.

Why Does My Ring spotlight flash on and off?

A low battery, a small animal or anything activating the device, or a setting on the motion sensitivity settings that is too high are the most common causes of the Ring Spotlight flashing on and off.

How do I restart my ring camera app?

Rebooting the Ring Spotlight Cam is a simple process.

  1. To reset the spotlight camera, press the reset button located on the top of the device. Holding down the reset button for twenty seconds will do this. Once the wifi connection has been restored, check your Ring app to see whether the spotlight cam displays as an accessible device once more.

Why is my ring floodlight flashing blue?

Most of the time, if your Ring Chime Pro is blinking blue, this indicates that it is either booting up, installing an update, or attempting to reconnect to Wi-Fi. When charging the Ring Doorbell Pro, you will need to wait for a few hours until it is completely charged and active.

Leave a Reply

Your email address will not be published. Required fields are marked *